Air Mass Dilemma

[motorman3]

Greetings, everyone.

I am receiving many trouble codes on my 2010 E350.


The initial focus is on the Air Intake Temperature sensor, which I intend to replace due to the original appearing contaminated, and the cost is sufficiently low.

I was informed that the codes are associated with a defective MAF sensor.

Enclosed are the codes and the real-time readings from my Maf sensors.

Unplugging sensor B results in a value of 0g. Upon disconnecting Sensor A, the readout displays 166g, while Sensor B subsequently increases to 8g.

I am willing to invest in a replacement MAF but seek guidance before making any purchases.

[motorman3]

https://www.ebay.co.uk/sch/i.html?_nkw=air intake&campid=5338181132&customid=2518X1570512Xa5862ada839b69684cb317f814483ddf&mkcid=1&mkrid=710-53481-19255-0&subId2=15&toolid=10001

[motorman3]

[motorman3]

I have recently replaced the temperature sensor, and I am not surprised that it did not resolve the issue.

I have observed that when I disconnect Sensor A, its temperature remains at 79°C whereas Sensor B decreases to 21°C.
Upon disconnecting Sensor B, both temperatures stabilise at 79°C.


The subsequent course of action appears to be attempting a costly MAF replacement, unless anyone possesses other insights.

[BENZE220AMG]

How is it functioning?Whenever I experienced MAF failure, the vehicles operated quite poorly.

[EnchantedScribe]

I am uncertain if this information would be beneficial, however when my MAF sensor went down due to a missing fuse, a prominent characteristic was difficult upshifts. If your vehicle is an automobile and you are encountering the same issue, it likely indicates a malfunctioning MAF sensor. - supposing that MB configures the gearbox ECU to default to elevated line pressures in the absence of MAF sensor data, consistent with my 4L 80E.

[NAVITEL]

Does a new MAF sensor require coding or is it plug-and-play?

[NAVITEL]

https://www.ebay.co.uk/sch/i.html?_nkw=maf sensor&campid=5338181132&customid=2518X1570512X4861dcd0c021bdde75eea8eb0758e1a7&mkcid=1&mkrid=710-53481-19255-0&subId2=15&toolid=10001

[motorman3]

I ultimately resolved the issue. The MAF was indeed defective. I purchased a pre-owned Y-Pipe in superior condition than mine, which included one MAF. I transferred my functional MAF to it, and it accurately registered the temperature and airflow readings.

Nevertheless, I occasionally have a minor hitch after startup. During discussions with Avantgarde in Clevedon, they indicated that the adjustments must be recalibrated for optimal performance. The issue is that I currently reside in Scotland, necessitating the search for a reputable independent establishment in Edinburgh. All local garages I have contacted have provided a standard quotation of approximately £90 for one hour of service. I would be more advantageous to purchase a superior fault reader for the two minutes required to reset it.

[NAVITEL]

You may reset it by disconnecting the negative battery terminal for 10 minutes.

[motorman3]

Disconnected the negative terminal for 20 minutes while replacing the fuel filter today. Currently, it is idling more effectively.

[KOOLCAR]

It is advisable to inspect all o-rings and seals on the turbo outlet (aluminium pipe) connecting to the resonator (plastic box at the front of the engine) and the intercooler. I believe your 2010 model possesses the same or a highly comparable engine to my 2009 E280. I recently completed all my maintenance, and the vehicle performs significantly better than before. I previously underestimated its condition, but I now recognise the sluggishness in throttle response and downshifts.


Some of these seals may have been compromised during the installation of the new intake; this is how I realised mine need attention, as I subsequently experienced a check engine light owing to many leaks, including a boost leak at the intercooler pipe.

I wanted to bring this to your attention, although you may already be aware.

[motorman3]

Indeed, I completed all necessary tasks when I replaced the thermostat, so I believe I am adequately prepared in that regard. I observed typical oil spots around the seal positions, which had been improperly installed. It appears that the new MAF required calibration in my situation.